Innovation & Quality


 

 

Until very recently, rockets that launched satellites into orbit were completely discarded after a single use -and this is still commonly done for most launches. Within the past year, first generation reusable satellite launch has been demonstrated, and the business case for reusable launch has been made.

As a prime contractor for the Defense Advanced Research Projects Agency (DARPA) Experimental Spaceplane (XS-1) program, Masten Space Systems is developing a launch vehicle with design innovations focused on next-generation reusability. DARPA’s XS-1 program aims to reduce the time to space and cost to space by orders of magnitude by achieving aircraft-like reusability and flight rate [1] . Jess Sponable, DARPA XS-1 program manager, has stated: “We think flying ten times in 10 days is something well beyond the capability of either SpaceX or Blue Origin at this time.” [2]

 


Artistic rendering of the XS-1 vehicle
Artistic rendering of Masten’s Xephyr post upper-stage-separation, before returning to land. | Courtesy of Masten Space Systems.

"Masten Space Systems heavily utilized the FINE Suite at HPC scale to design our next-generation reusable satellite launch system. We developed an aerodynamic configuration that hasn't been done before for launch or reentry. First wind tunnel tests confirmed critical aspects of the design, and predictions compared well with measurements." --Allan Grosvenor, Aerodynamics Lead at Masten Space Systems.


 

Requirements include cost per flight of less than $5 million USD transporting 3,000 lbs to a 100 nmi reference orbit inclined 90 degrees. Masten engineers needed to optimize the booster design over a wide range of flight conditions, including ascent from sea level to hypersonic speeds at the upper-stage-separation point, and then reentry and return flight.

NUMECA-USA has worked closely with Masten Aerodynamics Lead, Allan Grosvenor, and his team to develop an HPC-driven workflow that enables concept development, evolution, and optimization, of vehicle configuration that takes into consideration aerodynamic performance, control, loads and aerothermal heating, with simultaneous trajectory optimization.

A study of the HIFiRE-1 high speed transition experiment was one of several test cases used to validate NUMECA solver predictions (Figure 1). The HIFiRE-1 experiment (Wadhams, et. al. 2008) is a Cone-Cylinder-Flare configuration, exposed to Mach 7.2 flow (Re 1E7) conducted at the CUBRC LENS hypersonic tunnel. The numerical results are shown to capture relevant physics and to predict pressures and heat fluxes, and particularly the peak heating which is critical to thermal protection system design.


HIFiRE-1 Validation
Figure 1. Above: HIFiRE-1 experimental rig. Below: Comparison of FINE/Turbo CFD solution vs. experimental data [4]. | Courtesy of Allan Grosvenor, Masten Aerodynamics Lead


To illustrate the optimization process we created a fictitious high speed flight vehicle test case inspired by the Colonial Viperfighter craft of the TV series Battlestar Galactica.

The ship design is controlled parametrically with NUMECA's AutoBlade™ modeler. A set of parameters control the canopy's length and height, the wing and vertical stabilizer angle and sweepback, and the nose radius and droop (Figure 2). Extensive sets of parameters are available for more detailed 3D shaping and variation of all portions of fuselage, lifting and control surfaces, etc.


Animation of AutoBlade Parameterization of the Colonial Viper craft
Figure 2. Parametric design variations controlled with AutoBlade™


Design necessarily required consideration of entire launch and return trajectories. Large numbers of organized studies conducted by Masten Space Systems included running sweeps through several critical flight conditions including variation of flight angles (e.g., pitch, yaw, roll) and aerodynamic control surface angles. The example shown here illustrates a subset of these studies focused on reentry.

DoDHPCMP supercomputers [3] were leveraged to conduct the extensive studies, and the Computational Pipeline (Figure 3) indicates the organized workflow that was executed to run the sophisticated design evolution process. Masten Space Systems found that only with NUMECA could they systematically produce high-quality grids (flow domain discretization) and high accuracy solutions.


HPC Workflow - Masten - NUMECA
Figure 3. HPC computational pipeline. | Courtesy of Masten Space Systems


The meshing task was automated with HEXPRESS / Hybrid™, which is the new generation multi-core meshing tool of NUMECA. It has been designed to generate meshes of complex geometries, regardless of the CAD format and quality (Figure 4).

Hexpress/Hybrid approach
Figure 4. Comparison of standard meshing practices vs. NUMECA's efficient approach.


This tool produces full hexahedral and hex-dominant meshes completely in parallel and in batch mode, which has been the perfect match for Masten's challenge. Masten Space Systems chose to utilize the option producing pure hex meshes.

Mesh views of Colonial Viper
Figure 5. CFD grid views of the Colonial Viper model. | Courtesy of Masten Space Systems


The CFD simulations were all executed with NUMECA's FINE™/Open CFD solver, and then post-processed through scripts running all in batch in a fully automatic way. Data-mining of the full 3D solutions feeds the optimization process.

The following animations are comparisons between the baseline vehicle and the new design for reentry performance and stability.


Comparative animation of Colonial Viper reentry Comparative animation of Colonial Viper reentry
Figure 6. Reentry Matrix Results Comparison: Baseline (left) vs Modified (right) designs


Images of Performance Cartesian Plots
Figure 7. Performance and stability plots showing how optimized design is significantly better than baseline model. | Courtesy of Masten Space Systems


For more information about NUMECA software products and consulting services, please visit our website or call +1(415)558-8483.


 

Mentioned in This Article

Masten Space Systems Logo - Black is lowering the barriers to space access. Their mission contributes to a shared strategic goal of extending human presence across the solar system. Their approach: reusability. Their technology development focuses at the core on entry, descent, and landing technologies (EDL) to ensure precise and safe landings on planets and other celestial bodies. Learn more

NUMECA International Logo is recognized today as the most innovative company in the field of Computational Fluid Dynamics (CFD) and Multiphysics analysis and optimization. Driven by creativity, innovation, and quality, we develop software toolsets that support the world's leading industries" Learn more

[1] DARPA pushing new effort with Experimental Spaceplane, XS-1 (nasaspaceflight.com)

[2] DARPA experimental spaceplane program moves into next phase (spacenews.com)

[3] Supercomputers Lower the Cost of Space Access (digitaleng.news)

[4] HIFiRE-1 Mach 7 aerothermal heating prediction (researchgate.net)

Share this article

Comments

Leave first comment here...

LEAVE A COMMENT

 
  • Would you like to know more?
    Click below to get in touch.